Next I took out my new HDD and put it in another machine, Installed XP with No Problem. I also tried a different IDE cable, same problem. I am sure that there is nothing wrong with the CD drive, because I also use RIS (Remote Installation Service) which allow me to perform install through the network. Michael Caruso Mar 24, 2006, 10:45am EST Reply - Quote - Report Abuse Private Message - Add to Buddy List Edited: Mar 26, 2006, 11:43am EST >>Re: "setup cannot copy http://introbuilder.net/windows-xp/windows-xp-cmprops-dl-copy-error.php
This process will enable you to run a search through the Start Menu. Newsletter A weekly newsletter featuring an editorial and a roundup of the latest articles, news and other interesting topics. Step 1:Download the Cmprops.dll library After clicking the "Download" button at the top of the page, the "Downloading" page will open up and the download process will begin. As further verification, I added the fourth known bad module to the other three and once again the computer would not properly boot (or, again, shut off).
Right-click the "Command Prompt" search result that comes up and click the Run as administrator" option. On the CD, _ is in the file type when I check properties, so I think the full filename is LICWMI.dl_ 0 FC Jamison 31 10 Years Ago Are you wiping Also is the _ in the filename on the cd? I have tried two XP CDs and two CD drives with the same result, and I got a new hard drive and still had these problems.
hope u can help me.. Vu Nguyen Mar 02, 2006, 06:13pm EST Reply - Quote - Report Abuse Private Message - Add to Buddy List >>Re: "setup cannot copy file" error when installing windows XPHi I'm not sure even that will work... It worked fine.
In other words, you must copy the "Cmprops.dll" library into both directories. First, my problem: I wanted to do a repair install of Windows XP. I tried to fix the MBR to get Windows XP back by putting in my Windows XP SP1 CD and going into the Recovery Console. However, I did not remember the administrator's password and my user name and password (despite having full administrator access) could not be used to log in.
Browse other questions tagged windows windows-xp installation windows-installation windows-2003 or ask your own question. Put the HDD from the Other machine (Which I know works) into my machine and tried installing. I was a little confused because Memtest86 pretty much just takes off when you start your computer (and, as he states on his website, will run indefinitely). I repeated this until I had tested each module individually.
The solution: 1. Next I took out my CD RW and replaced it with a new one and tried installing again. Scanning Status (% complete) 0 10 20 30 40 50 60 70 80 90 100 |----|----|----|----|----|----|----|----|----|----| ................................................... So this rules out any problem with:- The CD The CD RW The HDD This leaves My motherboard or my IDE cable?
Thanks in advance for any ideas, travis smoto smoto Aug 20, 2004, 01:36am EDT Reply - Quote - Report Abuse Private Message - Add to Buddy List >>Re: "setup cannot http://introbuilder.net/windows-xp/windows-xp-installation-copy-error.php Within a few minutes I also received an email verifying all the information. Hitting cancel to skip that file, I went through 25 of them before giving up. I rebooted off the Windows install CD, and hit R to go to the repair console.
My issues started with the "setup cannot copy the file cmprops.dl_" and went on from there not copying files. Navigate to the \%windir%\security folder by typing cd %windir%\security Remove the edb0000x.log file by typing del edb0000*.log You'll then be able to perform the in-place upgrade. Bottom line: I think if you see red, that's a bad thing. http://introbuilder.net/windows-xp/windows-xp-sp3-copy-error.php Click here to become a Hardware Analysis registered user.
I have since solved the problem, and wish to post the solution here for future Google searchers. Also, is it possible to get some version of DOS on a CD ? Then I rebooted the computer without going into the CD, and let the Windows installer continue (where in previous reboots it complained of not being able to copy files again).
Run the program giving the dll error again. I figure that this means that there is some error in the mbr.. And then I deleted c:\windows\security\edb0000x.log. Database: C:\WINDOWS\security\database\secedit.sdb Temp.
I am using the same winXP cd (which isn't scratched at all). So, double-click the file with the ".zip" extension that you downloaded and open the file. Delete file edb.log (it might be edb00001.log or something like) 5. useful reference And this time, there was no complaint of inability to copy files.
Open the Start Menu and before clicking anywhere, type "cmd" on your keyboard. I then proceeded to delete c:\windows\security\edb.log. I decided to just press esc and skip all the files it was complaining about... Tks for any info !
Esentutl will confirm the repair by displaying a log file similar to the following example: Microsoft(R) Windows(R) Database Utilities Version 5.2 Copyright (C) Microsoft Corporation. This time will change according to your computer's performance and the size of the program. Trick or Treat polyglot Is there an illusion in the tutorial area? If you delete all the partitions, redo them in NTFS, do a full format, and try again with a new CD that should work.Michael A.
Type Taskmgr.exe in the DOS window and press enter. Right-click the "Command Prompt" search result that comes up and click the Run as administrator" option. Why do I receive a file-copy error when I perform an in-place upgrade of Windows Server 2003? So, here's the solution: I did this based off of http://support.microsoft.com/kb/818464.
When you perform an in-place upgrade of Windows Server 2003, you receive 'Setup cannot copy the file