Home > Windows 98 > Windows 98 Modem Error 630

Windows 98 Modem Error 630

If the modem is external; turn the modem off and then back on. Once you have completed the boot process, try to connect to Hamilton County Communications again. Removing the Windows Password List Windows keeps a list of passwords for the users on the system. Click on the Add button to begin reinstalling your modem.

Programs in the StartUp folder can also cause this error message. Disable call waiting (if you have that service), and then dial Hamilton County Communications. If the modem does not have a switch, you may need to unplug it from the wall. Make sure that your modem is selected in the drop-down menu.

In both cases, the modem should respond with a dial tone or communication signal. Click OK. Adding the Extra Setting Click on the Start button, then Settings | Control Panel.

Select the Windows Setup tab. Click on your modem to select (highlight) it. If you are still having problems reinstall your modem, and call your ISP. __________________________________________________________________________________ Error 676: The Line Is Busy. Be sure that the phone line is plugged into the jack labeled Telco or Line, and not the jack labeled Phone.

Article ID: Q190554 Error630: The computer is not receiving a response from the modem. Uncheck ‘Use Default Gateway on remote server’. Close all running programs, saving your work as you do so. If asked to confirm your new password, click OK.

Repeat this for all of the components in the list. On the WINS tab, select Disable. Select Shut Down and press OK. L3 is a universal command to raise the modem's speaker volume to the maximum level if it is at the lowest by default.

Select the COM port on which your modem is installed and click on More Information. http://www.cubamex.com/airam/TechSupport/error630.htm The easiest way to remedy this problem is to power cycle your computer. Error 630: The computer is not receiving a response from the modem. Dial-Up Networking Reports "Error 630" When you attempt to use Dial-Up Networking, you may receive the following error message: Error 630: The computer is not receiving a response from the modem.

NOTE: If your modem is not listed, the driver is not installed properly or at all, and your modem cannot be tested. If WINS Resolution is enabled, then disable it. Programs run at StartUp from the StartUp folder can also cause this error message. This causes Banyan VINES to try to operate over an IPXODI protocol stack, which it is not designed to do.

Uncheck Dial Up Networking. Double click on Dial Up Networking. To determine if this is the case, see the appropriate section below. Click Find Now.

If the Client for Microsoft Networks is not listed: Click on Add Double click on Client Highlight Microsoft in the left pane. You may need to look in the start menu programs to see what is being loaded on startup; and close anything that might be holding the modem open. For more information about Windows-only modems and how to troubleshoot them, obtain the US Robotics Windows-only modem FAQ from the following 3Com U.S.

Right click on the Hamilton County Communications icon and select Properties.

If the file is not found, make sure that your drive letter is correct for your CD-ROM drive and that the CD that you are using is the same one from Make sure that your modem is selected in the drop-down menu. Next we need to make sure that TCP/IP is properly configured. For more information about using the System File Checker tool, please see "System File Checker Tool" section of the following article in the Microsoft Knowledge Base: ARTICLE-ID: Q129605 TITLE : How

Windows will ask you which port that the modem should be installed on. Select the Connection tab. NOTE: Hardware using the IRQ Holder For PCI Steering setting can be disregarded. Select Server Assigned IP Address in the first section.

Once you have completed the boot process, try to connect to Hamilton County Communications again. Click on the Start button. Enter Hamilton County Communications as the name of the connection. Re-install Dial-Up Networking.

Error 629: The Port Was Disconnected by the Remote Computer Back to the top This is an error associated with Dial Up Networking and can be caused by an incorrect setting If the Client for Microsoft Networks is not listed: Click on Add Double click on Client Highlight Microsoft in the left pane. Right click on the Hamilton County Communications icon and select Properties. In some cases however, a Windows-only modem that conflicts with another device may not have an exclamation point in a yellow circle.

Identifying the Modem Disconnect any active connections. On the Gateway tab, remove any installed gateways. How to Configure Windows Network Components Important Notice: These instructions assume that you are using a modem to connect to Hamilton County Communications from a standalone computer.