Home > Windows 98 > Windows 98 Invalid System Disk Error

Windows 98 Invalid System Disk Error

If you see FAT16 or FAT32 in fdisk press the ESC key until back at the A:\> Once at the A:\> Type, sys c: (only do this command if If CMOS indicates the drive is not installed or not detected skip to Hard drive is bad or not connected properly. Right now, we know nothing about the system you're working on, so no one can provide you anything except general suggestions. I put in another CD. Source

I found this to be a common problem with win98.There is no recovery console for win98.You can boot from the original cdrom and select:"Start the computer with cd-rom support"This will boot Yet these computer manufactures can't even make a laptop to be built with a boot to Dos Prompt command at the start up. If you've tried the above options without success try resetting the CMOS. It started to boot and the windows splash screen showed up. https://forums.techguy.org/threads/solved-invalid-system-disk-windows-98-problem.425513/

Quote: When I try to hit detect hard drive and set it to automatic it shows nothing, then I tried user and still it didn't detect the hard drive. Advertisements do not imply our endorsement of that product or service. I know the hard drive was working fine, before I ran fdisk.

Not to mention the difficulties that Windows gives you by no being able to uninstall windows if it is the only operating system on your computer. Anyone else reading this have any ideas? You're looking for the screen that shows you the harddrive information, because that is most likely where the setting for the floppy drive is kept. Información Prensa Derechos de autor Creadores Publicidad Desarrolladores +YouTube Términos Privacidad Política y seguridad Enviar sugerencias ¡Prueba algo nuevo!

thanks a lot guys, "Beam me up Scotty" --Captain Kirk USS Enterprise Reports: · Posted 5 years ago Top UKHank Posts: 1 This post has been reported. You know what I am saying? I'll let you ponder for a bit. over here Connect with us facebook twitter CNET Reviews Top Categories CNET 100 Appliances Audio Cameras Cars Desktops Drones Headphones Laptops Networking Phones Printers Smart Home Software Tablets TVs Virtual Reality Wearable Tech

Triple6 replied Nov 1, 2016 at 12:48 PM XY coordinate on top of area chart Masta Squidge replied Nov 1, 2016 at 12:47 PM Locked out of Windows - Auto... FWIW, the missing pin you mentioned is to help make sure you install the floppy cable in the proper position. The system files that are missing are Io.sys, Msdos.sys and Command.com. TechSpot Account Sign up for free, it takes 30 seconds.

Put it back in your computer, boot, change to the directory and install.

I've also found the ATTRIB app within the EBD folder, but I'm going to need some assistance changing those attributes to whatever they need to be changed to. Now if the hard drive shows up when it starts, then it means the BIOS is picking it up. Transcripción La transcripción interactiva no se ha podido cargar.

For example, most computers should have their boot options setup similar to the example below.- Floppy drive- CD drive - Hard drive Reset your CMOS to default values. this contact form Something that would look similar to this: ----------------------------------Ignorance is not necessarily Bliss, case in point:Unknown has caused an Unknown Error on Unknown and must be shutdown to prevent damage to Unknown. I can't believe that I need two windows CDs just to run one computer, grrrr. When it is set to User and LBA the computer goes through the boot process, detects the cdrom drive and the floppy drive, but does not list detecting the hard drive.

Look through the posts.How many emergency fixes start with the lowly floppy and useless DOS? Some people consider the floppy disk obsolete, but I still install one in every system I build; I consider it an essential tool because optical drives can't always read the disks An extra drive letter popped up, Drive D. have a peek here My solution was to enter the bios (Phoenix/Award 2003) go to the advanced options and change the "Boot Sequence". 1st Boot Device [CDROM] 2nd Boot Device [HDD-0] 3rd Boot Device [HDD-1}

illuminate during POST?Often you can hear the drive "grunt" during this process...If yes to the above, then maybe the floppy drive is out of alignment.Try changing the drive for a known Back to top #7 Keithuk Keithuk Members 943 posts OFFLINE Gender:Male Local time:05:56 PM Posted 30 April 2009 - 07:20 AM I took that floppy and inserted in another machine I have about 15-20 spare hard drives laying around and I have swapped out a working ME drive to no avail.

A small, free program to do this can be downloaded at:http://www.terabyteunlimited.com/downloads/burncdcc.zip.

I have a 20GB HD and it takes 40 minutes to check my drive.I do not have a Windows ME original disk. Fixing the mbr allowed me to pick up from the original hang. I put Hard Drive #2 in Laptop #1. Invalid System Disk error irishz (TechnicalUser) (OP) 24 Aug 07 13:01 I changed 3 floppy drives and also the cables and the floppy light is coming on when i have the

Inicia sesión para informar de contenido inapropiado. I'll try the HD delay first, and if that doesn't work, I'll try this. Look for printing silk-screened on the board to help identify it; tell us everything you see on the monitor when you first boot the system. http://introbuilder.net/windows-98/windows-98-boot-disk-error.php thanks everyone for you help, this has helped me figure out a way to accomplish this problem, with one problem solving technique at a time.

Sorry, there was a problem flagging this post. Share Flag This conversation is currently closed to new comments. 7 total posts (Page 1 of 1)   + Follow this Discussion · | Thread display: Collapse - | Expand + I don't know what to do now???? Register now while it's still free!

You need KILLDISK software downloaded from cnet.com, a blank CD or DVD disk and ISO burning software. In fact, it is the reason why another Laptop that I have no longer runs.... Join Us! *Tek-Tips's functionality depends on members receiving e-mail. R.

Please re-enable javascript to access full functionality. Because I really don't know much about Linux. Or, having you guys help me fix it.I have a question.