Home > Windows 7 > Windows 7 Sp1 Dual Boot Error

Windows 7 Sp1 Dual Boot Error

Contents

You can insure the partition is being mounted by running a command prompt elevated as Administrator and entering “mountvol /E” at the command prompt. I did have an extra drive installed that is for back up and I tried removing that but the error still persists. I've seen many instances of this now being due to dual boot Linux installations as you mentioned. Essentially i want a normal windows 7 computer, with a secondary hard drive that has the full ubuntu OS installed on it, but the only way to load it up and have a peek at this web-site

The following files corrupt and unreadable: F:Windowsassembly F:WindowsOffline Web Pages F:WindowsModemLogs F:WindowsPLA F:WindowsPerformance After some researching, I found this article: http://support.microsoft.com/kb/176646 "WARNING: When Chkdsk detects problems with the file system and Then I rebooted and voila — SP1 installed without a hitch. sudo update-grub Reply ↓ Nailsea on January 31, 2012 at 10:51 am said: Just the info I was looking for. Password FAQ Calendar Today's Posts Search Search Forums Show Threads Show Posts Advanced Search Go to Page... have a peek at this web-site

Windows 7 Sp1 Error 0x800f0a12

A manual check brought it back but the file size showed 73.6MB-892.6MB to this date. I don't know which one is which. Press ‘Enter’. ->Restart you system and give one more attempt to install SP1. If you're lucky enough to have separate HDDs for your windows install and other OSs just change the boot order in the bios temporarily for the update.

Got error 0x800f0a12 at initial try (3-4 times) 2. Adv Reply February 23rd, 2011 #10 M3rc Nate View Profile View Forum Posts Private Message 5 Cups of Ubuntu Join Date Jun 2010 Location Seattle Beans 27 Re: Dual Boot I've even tried mounting the FAT partition thinking that might have it confused but no luck. Reply joscon [Microsoft] says: November 1, 2016 at 4:28 pm Yes, it looks like those are missing based on the logs.

Reply ↓ Vio on March 23, 2014 at 11:41 pm said: cmd-mount vol /E worked for me.Thanks. Service Pack Installation Failed With Error Code 0x800f0a12. I have Widows 7 on sda1&2 and an extended partition with SuSe 11.2. So to boot to the sixth item in the list, the line would read GRUB_DEFAULT=5. http://www.zdnet.com/article/quick-fix-for-windows-7-sp1-installation-errors/ Thanks to Joseph for writing the article and Ed Bott for bringing it to my attention on Twitter and thanks to all those writing comments to help out the rest of

During installation of Windows 7 I had to add the hardware raid pci card driver to be able to start installation. So, one more thing to add to the lore of how to get around this issue. Still, there are a few updates included in SP1 that people will want to take advantage of — many of which are performance related. My Fujitsu laptop come natively with a small (~ 150 MiB) partition storing the Windows boot files.

Service Pack Installation Failed With Error Code 0x800f0a12.

The sad, sad bit of code apparently had decided to overwrite grub regardless of the fact that it was on a different disk, and the /other/ bootloader on the actual windows https://blogs.technet.microsoft.com/joscon/2011/02/17/windows-72008-r2-service-pack-1-fails-with-0x800f0a12/ i'm afraid to touch the BCD since i have no way of restoring the SmartON OS if it's fudged. Windows 7 Sp1 Error 0x800f0a12 This same solution solved the error on all the computers I encountered the 800F0A12 error on. Mountvol /e Raid configuration is to stripe (I'm looking for speed).

I dont know exactly what you mean. Check This Out Go on repeating the steps again and select ‘Run as Administrator’ given in step 2. Best laugh I had all day for sure. Reply Stromi says: May 16, 2013 at 8:51 pm Joscon you're the best ! 0x800f0a12 Windows 2008 R2 Sp1

Motherboard asus P5B-e. But no confirmation at this point and it may also be due to entering the wrong password on reboot (you have to reboot a couple times in certain situations) This upgdate After everything is installed properly, I can change the settings back to the above. Source ZDNet Gravatar ExEC135CrewDog 02/24/2011 11:39 AM ******************************** RE: Quick fix for Windows 7 SP1 installation errors @Loverock Davidson It's a windows disk check problem.

If I don't succeed I will just remove win7 from this laptop and don't use it any more. Or is there any way that I can (without re-installing Windows) rebuild the backup from the original source media? I hit the left arrow key to select Win7 most of the time.

Reply NapO says: February 25, 2011 at 12:21 pm easy fix for this one.

Reply ↓ Dabeastro on December 11, 2011 at 8:40 pm said: Same solution as Sprewell. Install SP1 An additional link: http://windows.microsoft.com/en-US/windows7/windows-7-windows-server-2008-r2-service-pack-1-sp1-installation-error-0x800F0A12 If your problem is not automount policy then you might have one of the other scenarios which can cause this error to occur (such as The time now is 05:28 PM. In that case the BOOT folder will be created on drive C.

But I will move this to the Windows 7 section. NOTE: The Disk Management tool will show which partition is "Active" and, since you've got the error, that will not be the one where Windows 7 lives. I'll update the blog shortly. have a peek here Run the following command: select disk 0 list partition select partition x active x is the partition of Windows, you can look at the partition size to recognize it. 3.

To enable autmount, just follow the steps above. What I didn't realise is that because I run with UAC disabled I automatically had the SP backup files included in my last clean-up run. Following the definition of insanity and going back to Microsoft Update to try again and again does not usually fix the problem.